Amp and Speaker Cabinet Selectors

The de Lisle Amp-Speaker Selector (Version 1) was designed as a studio tool to conveniently route the output from any of the connected amplifiers to an isolation cabinet. Alternatively, a single amplifier can be paired with one of up to three individual cabinets. Signal and ground connections from the amps are isolated, and as a precaution, the unused amps see a load. Similarly, when used as a cabinet selector, jacks with no cable inserted will be switched to an internal load. So, one can use a single cabinet or two cabinets without worrying about switching to an open cabinet jack.

The de Lisle Speaker Cabinet AB Selector Switch allows you to toggle between two speaker cabinets connected to the same amp. If your amplifier has multiple output jacks for different impedance cabinets, you can connect a second output to the ALT Z jack and toggle between two cabinets connected to different impedance outputs on the same amp. There's also a remote input that will allow you to operate the switch from a distance with a simple TS latching switch.

Save 15% with the Amp-Speaker Selector V3 and Drop Box 50W Linearly Variable Attenuator bundle! Add our transformer isolated ABC switch to route the input signal for more savings!

The de Lisle Amp-Speaker Selector V3 was designed as a studio tool to conveniently route the output of up to three amplifiers to various speaker cabinets. This version features a loop to allow a single attenuator or similar device to be easily shared between any combination of the amps and speakers.

Just connect your amps' outputs to numbered amplifier inputs on the rear panel. Then, hook up your speaker cabinets. Routing the signals is simple: the three Speaker switches on the front panel correspond to the three speaker connections. The 0-3 positions of each bank match that speaker cabinet to an amplifier (or 0 for not connected).

Connect your attenuator's input to the Send jack and its output to the Return jack. Use the front panel Send knob to connect the attenuator to any of the amps' outputs. Then, set one or more of the Speaker knobs to the return arrow icon (position 5).

Use multiple amps at the same time, swap speaker cabinets between amps, share a single attenuator or connect multiple speakers to an amp in parallel. Signal and ground connections from the amps are always isolated from one another. And as a precaution, the unused amps see a load.

The de Lisle Amp-Speaker Selector V2 was designed as a studio tool to conveniently route the output of up to four amplifiers to various speaker cabinets. Just connect your amps' outputs to numbered amplifier inputs on the rear panel. Then, hook up your speaker cabinets. Routing the signals is simple: the four switches on the front panel correspond to the four speaker connections. The 0-4 positions of each bank match that speaker cabinet to an amplifier (or 0 for not connected). Use multiple amps at the same time, swap speaker cabinets between amps, or connect multiple speakers to an amp in parallel. Signal and ground connections from the amps are always isolated from one another. And as a precaution, the unused amps see a load.

Bundle with our Amplifier Input Selector 6x to save $100!

The de Lisle FX Loop Router allows you to effortlessly share your FX between up to 8 amps.

Plug your FX into the rear panel FX Input and FX Output jacks. Then rotate the Amplifier dial to route your FX to any of the connected amp loops. Unused amps are placed in bypass mode to prevent noise. We've also included a front panel Bypass switch for the selected amp and a Ground switch to help eliminate noise.

The FX Loop Router runs off a standard 2.1mm/5.5mm center negative 9V supply (included). We've also provided a "daisy chain" extension jack, so you can connect external 9VDC powered devices.

Desktop model shown. Rackmount enclosure available as an option.

The de Lisle Amplifier Input Selector 6x was designed to be paired with our Amp-Speaker Selector models that only do speaker to output routing to increase functionality.

Split the input signal to up to six amplifiers via the front panel toggle switches. You could also run a dry signal to your DAW and/or a tuner. Lots of possibilities. Each rear panel output is transformer isolated to avoid any ground loop issues. Bundle with our 1U Amp-Speaker Selectors or V2 to save $100.00! (Links to those products are below.)

The Amplifier Input Selector 6x runs off the provided 2.1mm/5.5mm center negative 12VDC supply. It can also be powered by a standard 9VDC center-negative power supply.

The de Lisle Amp-Speaker Selector 4x4 with Stereo Attenuator Loop Return was designed as a studio tool to conveniently route the output of up to four tube amplifiers to various speaker cabinets. This model features an attenuator loop to allow a single attenuator to be shared between any combination of the amps and speakers. It was developed specifically with the Two Notes Reload II, Boss Tube Amp Expander and similar products. The 4x4 with Stereo Attenuator Loop Return allows you to assign speakers to both outputs of the attenuator to easily create a flexible wet-dry-wet setup. Use up to 4 amps simultaneously.  

Just connect your amps' outputs to numbered amplifier inputs on the rear panel. Then, hook up your speaker cabinets. Routing the signals is simple: the four Speaker switches on the front panel correspond to the four speaker connections. The 1-4 positions of each bank match that speaker cabinet to the selected amplifier.

Connect your attenuator's input to the Send jack and its speaker output(s) to the Return A and/or B jacks. Use the front panel Send knob to connect the attenuator to any of the available amps. Then, set one or more of the Speaker knobs to the Return A/B position.

Use multiple amps at the same time, swap speaker cabinets between amps, share a single attenuator or connect multiple speakers to an amp in parallel. As a precaution, the unused amps see a load.

Bundle with our Amplifier Input Selector 6x to save $100!

The de Lisle Amp-Speaker Selector 8 x8 was designed as a studio tool to conveniently route the output of up to eight tube amplifiers to various speaker cabinets.

Just connect your amps' outputs to numbered amplifier inputs on the rear panel. Then, hook up your speaker cabinets. Routing the signals is simple: the eight Speaker switches on the front panel correspond to the eight speaker connections. The 0-8 positions of each bank match that speaker cabinet to an amplifier (or 0 for not connected).

Use multiple amps at the same time, swap speaker cabinets between amps, or connect multiple speakers to an amp in parallel. And as a precaution, the unused amps see a load.

Bundle with our Amplifier Input Selector 6x to save $100!

Note: this device is not compatible with some digital modeling amps or attenuators that feature a bridged mono power amp like the Two Notes Reload II. See the newer models below for universal compatibility.

The de Lisle Amp-Speaker Selector 7x7 with Attenuator Loop was designed as a studio tool to conveniently route the output of up to seven tube amplifiers to various speaker cabinets. This version features a loop to allow a single attenuator or similar device to be easily shared between any combination of the amps and speakers.

Just connect your amps' outputs to numbered amplifier inputs on the rear panel. Then, hook up your speaker cabinets. Routing the signals is simple: the seven Speaker switches on the front panel correspond to the seven speaker connections. The 0-7 positions of each bank match that speaker cabinet to an amplifier (or 0 for not connected).

Connect your attenuator's input to the Send jack and its output to the Return jack. Use the front panel Send knob to connect the attenuator to any of the amps' outputs. Then, set one or more of the Speaker knobs to the return arrow icon (position 9).

Use multiple amps at the same time, swap speaker cabinets between amps, share a single attenuator or connect multiple speakers to an amp in parallel. As a precaution, the unused amps see a load.

Bundle with our Amplifier Input Selector 6x to save $100!

Note: this device is not compatible with some digital modeling amps or attenuators that feature a bridged mono power amp like the Two Notes Reload II. See the newer models below for universal compatibility.

The de Lisle Amp-Speaker Selector 6x6 was designed as a studio tool to conveniently route the output of up to six tube amplifiers to various speaker cabinets.

Just connect your amps' outputs to numbered amplifier inputs on the rear panel. Then, hook up your speaker cabinets. Routing the signals is simple: the eight Speaker switches on the front panel correspond to the eight speaker connections. The 1-6 positions of each bank match that speaker cabinet to an amplifier.

Use multiple amps at the same time, swap speaker cabinets between amps, or connect multiple speakers to an amp in parallel. And as a precaution, the unused amps see a load.

Bundle with our Amplifier Input Selector 6x to save $100!

This device is compatible with solid state, modeling or tube amplifiers.