Related Products

• ￩

  ￫

  

  de Lisle Amp-Speaker Selector 4x4 with Stereo Attenuator Loop Return

  $499.00

  The de Lisle Amp-Speaker Selector 4x4 with Stereo Attenuator Loop Return was designed as a studio tool to conveniently route the output of up to four tube amplifiers to various speaker cabinets. This model features an attenuator loop to allow a single attenuator to be shared between any combination of the amps and speakers. It was developed specifically with the Two Notes Reload II, Boss Tube Amp Expander and similar products. The 4x4 with Stereo Attenuator Loop Return allows you to assign speakers to both outputs of the attenuator to easily create a flexible wet-dry-wet setup. Use up to 4 amps simultaneously.  
  
  Just connect your amps' outputs to numbered amplifier inputs on the rear panel. Then, hook up your speaker cabinets. Routing the signals is simple: the four Speaker switches on the front panel correspond to the four speaker connections. The 1-4 positions of each bank match that speaker cabinet to the selected amplifier.
  
  Connect your attenuator's input to the Send jack and its speaker output(s) to the Return A and/or B jacks. Use the front panel Send knob to connect the attenuator to any of the available amps. Then, set one or more of the Speaker knobs to the Return A/B position.
  
  Use multiple amps at the same time, swap speaker cabinets between amps, share a single attenuator or connect multiple speakers to an amp in parallel. As a precaution, the unused amps see a load.
  
  Bundle with our Amplifier Input Selector 6x to save $100!

  Maximum quantity exceeded

  Minimum purchase amount of 0 is required
  de Lisle Amp-Speaker Selector 4x4 with Stereo Attenuator Loop Return

  

  de Lisle Amp-Speaker Selector 4x4 with Stereo Attenuator Loop Return

  $499.00

  The de Lisle Amp-Speaker Selector 4x4 with Stereo Attenuator Loop Return was designed as a studio tool to conveniently route the output of up to four tube amplifiers to various speaker cabinets. This model features an attenuator loop to allow a single attenuator to be shared between any combination of the amps and speakers. It was developed specifically with the Two Notes Reload II, Boss Tube Amp Expander and similar products. The 4x4 with Stereo Attenuator Loop Return allows you to assign speakers to both outputs of the attenuator to easily create a flexible wet-dry-wet setup. Use up to 4 amps simultaneously.  
  
  Just connect your amps' outputs to numbered amplifier inputs on the rear panel. Then, hook up your speaker cabinets. Routing the signals is simple: the four Speaker switches on the front panel correspond to the four speaker connections. The 1-4 positions of each bank match that speaker cabinet to the selected amplifier.
  
  Connect your attenuator's input to the Send jack and its speaker output(s) to the Return A and/or B jacks. Use the front panel Send knob to connect the attenuator to any of the available amps. Then, set one or more of the Speaker knobs to the Return A/B position.
  
  Use multiple amps at the same time, swap speaker cabinets between amps, share a single attenuator or connect multiple speakers to an amp in parallel. As a precaution, the unused amps see a load.
  
  Bundle with our Amplifier Input Selector 6x to save $100!

  ADD TO CART CHECKOUT NOW

  de Lisle Amp-Speaker Selector 4x4 with Stereo Attenuator Loop Return

  $499.00

  ADD TO CART CHECKOUT NOW

  Successfully Added to your Shopping Cart

  Adding to Cart...
• ￩

  ￫

  

  de Lisle Amp-Speaker Selector 8x8 MKII

  $549.00

  The de Lisle Amp-Speaker Selector 8x8 MKII was designed as a studio tool to conveniently route the output of up to 8 amplifiers to various speaker cabinets. This version features a loop to allow a single attenuator (passive or active like the Reload II or Ox Box) to be easily shared between any combination of the amps and speakers.
  
  Just connect your amps' outputs to the numbered amplifier inputs on the rear panel. Then, hook up your speaker cabinets. Routing the signals is simple: select the desired amplifier with the Amplifier rotary dial and select the desired speaker cabinet with the Speaker rotary. You can activate an additional speaker by flipping the Extension switch. The Extension speaker will be added in parallel to the main speaker for additional tones, volume or to match impedance. For example, if one amp only has a 4 ohm tap, activating two 8 ohm cabinets will present the correct load to the amplifier.
  
  Connect your attenuator's input to the Attenuator In jack and its output to the Attenuator Out jack. Use the front panel toggle to bring the attenuator in or out of the circuit. There's also a handy Ground switch to prevent ground loops between connected devices.
  
  As a precaution, the unused amps see a load. Compatible with tube or solid state amps up to 150W.
  
  This unit operates on the supplied 12 VDC power supply.
  
  Bundle with our Amplifier Input Selector 6x to save $100!

  Maximum quantity exceeded

  Minimum purchase amount of 0 is required
  de Lisle Amp-Speaker Selector 8x8 MKII

  

  de Lisle Amp-Speaker Selector 8x8 MKII

  $549.00

  The de Lisle Amp-Speaker Selector 8x8 MKII was designed as a studio tool to conveniently route the output of up to 8 amplifiers to various speaker cabinets. This version features a loop to allow a single attenuator (passive or active like the Reload II or Ox Box) to be easily shared between any combination of the amps and speakers.
  
  Just connect your amps' outputs to the numbered amplifier inputs on the rear panel. Then, hook up your speaker cabinets. Routing the signals is simple: select the desired amplifier with the Amplifier rotary dial and select the desired speaker cabinet with the Speaker rotary. You can activate an additional speaker by flipping the Extension switch. The Extension speaker will be added in parallel to the main speaker for additional tones, volume or to match impedance. For example, if one amp only has a 4 ohm tap, activating two 8 ohm cabinets will present the correct load to the amplifier.
  
  Connect your attenuator's input to the Attenuator In jack and its output to the Attenuator Out jack. Use the front panel toggle to bring the attenuator in or out of the circuit. There's also a handy Ground switch to prevent ground loops between connected devices.
  
  As a precaution, the unused amps see a load. Compatible with tube or solid state amps up to 150W.
  
  This unit operates on the supplied 12 VDC power supply.
  
  Bundle with our Amplifier Input Selector 6x to save $100!

  ADD TO CART CHECKOUT NOW

  de Lisle Amp-Speaker Selector 8x8 MKII

  $549.00

  ADD TO CART CHECKOUT NOW

  Successfully Added to your Shopping Cart

  Adding to Cart...
• ￩

  ￫

  

  de Lisle Amplifier Input Selector 6x

  $449.00

  The de Lisle Amplifier Input Selector 6x was designed to be paired with our Amp-Speaker Selector models that only do speaker to output routing to increase functionality.
  
  Split the input signal to up to six amplifiers via the front panel toggle switches. You could also run a dry signal to your DAW and/or a tuner. Lots of possibilities. Each rear panel output is transformer isolated to avoid any ground loop issues. Bundle with our 1U Amp-Speaker Selectors or V2 to save $100.00! (Links to those products are below.)
  
  The Amplifier Input Selector 6x runs off the provided 2.1mm/5.5mm center negative 12VDC supply. It can also be powered by a standard 9VDC center-negative power supply.

  Select Options
  de Lisle Amplifier Input Selector 6x

  

  de Lisle Amplifier Input Selector 6x

  $449.00

  The de Lisle Amplifier Input Selector 6x was designed to be paired with our Amp-Speaker Selector models that only do speaker to output routing to increase functionality.
  
  Split the input signal to up to six amplifiers via the front panel toggle switches. You could also run a dry signal to your DAW and/or a tuner. Lots of possibilities. Each rear panel output is transformer isolated to avoid any ground loop issues. Bundle with our 1U Amp-Speaker Selectors or V2 to save $100.00! (Links to those products are below.)
  
  The Amplifier Input Selector 6x runs off the provided 2.1mm/5.5mm center negative 12VDC supply. It can also be powered by a standard 9VDC center-negative power supply.

  Select Options

  de Lisle Amplifier Input Selector 6x

  $449.00

  Select Options

  Successfully Added to your Shopping Cart

  Adding to Cart...