Pedals

The de Lisle Amp-Speaker Selector 8x8 MKII was designed as a studio tool to conveniently route the output of up to 8 amplifiers to various speaker cabinets. This version features a loop to allow a single attenuator (passive or active like the Reload II or Ox Box) to be easily shared between any combination of the amps and speakers.

Just connect your amps' outputs to the numbered amplifier inputs on the rear panel. Then, hook up your speaker cabinets. Routing the signals is simple: select the desired amplifier with the Amplifier rotary dial and select the desired speaker cabinet with the Speaker rotary. You can activate an additional speaker by flipping the Extension switch. The Extension speaker will be added in parallel to the main speaker for additional tones, volume or to match impedance. For example, if one amp only has a 4 ohm tap, activating two 8 ohm cabinets will present the correct load to the amplifier.

Connect your attenuator's input to the Attenuator In jack and its output to the Attenuator Out jack. Use the front panel toggle to bring the attenuator in or out of the circuit. There's also a handy Ground switch to prevent ground loops between connected devices.

As a precaution, the unused amps see a load. Compatible with tube or solid state amps up to 150W.

This unit operates on the supplied 12 VDC power supply.

Bundle with our Amplifier Input Selector 6x to save $100!

The de Lisle Amplifier Expander 4x was designed to be paired with our Amp-Speaker Selector models to increase the number of amplifiers available for use.

Integration is straightforward: plug in your guitar / pedalboard into the front panel input of the Amplifier Expander, connect the Input Thru jack to the front panel input of your existing Amp-Speaker Selector, connect the Output Link to a dedicated Amp Output position on the Amp-Speaker Selector.

When the 3-position power switch is set to Thru, the input signal bypasses the Amplifier Expander allowing the Amp-Speaker Selector to be used normally. To use the Amplifier Expander with the Amp-Speaker Selector, set the Amplifier rotary on the Amp-Speaker Selector to the position used for the Output Link. Set the power rotary on the Amplifier Expander to the Direct or Iso position. Select the desired amplifier on the Amplifier Expander. Its output will be sent to the Amp-Speaker Selector via the Output Link jack. The speakers and attenuator connected to the Amp-Speaker Selector will now be available to the amps connected to the Amplifier Expander.

The Amplifier Expander 4x runs off a 2.1mm/5.5mm center negative 12V supply, which can be used to power the Amp-Speaker Selector as well via the provided connecting wire. Older 9VDC versions can run on the original power supply.

The de Lisle Amp-Speaker 4x4 Deluxe was designed to improve workflow in the studio by eliminating the need to re-cable amps and cabs. This version expands on our previous designs by incorporating simultaneous input switching and a bypassable attenuator loop.

Plug in your guitar / pedalboard and send it to any of the 4 connected amps by rotating the Amplifier dial. The amp's output is then sent to the selected speaker cabinet. We've also included an attenuator loop that allows you to easily connect your Ox, Fryette, etc. to any combination of amplifier and cabinet.

The 4x4 Deluxe runs off a 2.1mm/5.5mm center negative 12V supply, which is boosted internally for increased signal headroom. Amplifier inputs are transformer isolated to prevent ground loops. Unused amps are muted at the input and switched to a protective load.

Desktop model shown. Rackmount enclosure available as an option.

New features for 2024 models:

There are now three options for amp input switching. DIRECT takes the front panel input and sends it directly to the input of the selected amp, bypassing any additional circuitry. This is the position for normal use. ISO, for ISOLATED, sends the input signal through an isolation transformer. This can be used to eliminate ground loops or when a low impedance output is desired. When the ground switch is in the left position, the isolation transformer is bypassed entirely and an op-amp buffer provides a low impedance output. Download the manual for the latest features and control layout.

Protected by US Patent

The de Lisle 100W Reactive Attenuator allows you to knock your amp's volume down to a more manageable level while maintaining its natural feel thanks to the reactive load. Attenuation is linearly variable up to -22.5dB. Our unique design eliminates the need for impedance matching at the amp. Just connect the attenuator to your amp's 8 ohm output, then you can use any combination of cabs as long as the total load is between 16 and 4 ohms. Use the transformer isolated D.I. to go straight into your DAW and load up your favorite IRs with the ability to record silently.

The de Lisle Pre-Amp Selector was designed to improve workflow in the studio by eliminating the need to re-cable when switching between numerous preamps and power amps.

Plug in your guitar / pedalboard and send it to any of the 4 connected preamps (or modelers) by rotating the Preamp dial. The preamp's output is then sent to the selected Power Amp. Alternatively, one could connect any line level device to the rear panel Power Amp Input jacks. So, one could be assigned to a power amp, another to a recording interface, external FX, etc. There is also an FX loop between the Preamp and Power Amp which can be bypassed on the front panel.

The Preamp Selector runs off a standard 2.1mm/5.5mm center negative 12VDC supply, which is boosted internally for increased signal headroom. Preamp inputs are transformer isolated to prevent ground loops. Unused preamps are muted at their input.

The de Lisle 100W Reactive Attenuator IR allows you to knock your amp's volume down to a more manageable level while maintaining its natural feel thanks to the reactive load. Attenuation is linearly variable up to -22.5dB. Our unique design eliminates the need for impedance matching at the amp. Just connect the attenuator to your amp's 8 ohm output, then you can use any combination of cabs as long as the total load is between 16 and 4 ohms. Use the transformer isolated IR Out to go straight into your DAW and load up your favorite IRs with the ability to record silently or use one of our 10 included impulse responses for a variety of high quality cabs sims.

Included Impulse Responses (See "Sounds" tab below):

01 Vox AC30
02 Marshall 1960AV
03 Marshall 2550
04 Orange PPC
05 Celestion Vintage 30
06 Tweed Bassman
07 Tweed Champ
08 Blackface Twin
09 Mesa Rectifier
10 Ampeg SVT
11 Bypass

The de Lisle Amp-Speaker 8x8 Deluxe was designed to improve workflow in the studio by eliminating the need to re-cable amps and cabs. This version expands on our previous designs by incorporating simultaneous input switching and a bypassable attenuator loop.

Plug in your guitar / pedalboard and send it to any of the 8 connected amps by rotating the Amplifier dial. The amp's output is then sent to the selected speaker cabinet. We've also included an attenuator loop that allows you to easily connect your Ox, Fryette, etc. to any combination of amplifier and cabinet.

The 8x8 Deluxe runs off a 2.1mm/5.5mm center negative 12V supply, which is boosted internally for increased signal headroom. Amplifier inputs are transformer isolated to prevent ground loops. Unused amps are muted at the input and switched to a protective load.

New features for 2024 models:

There are now three options for amp input switching. DIRECT takes the front panel input and sends it directly to the input of the selected amp, bypassing any additional circuitry. This is the position for normal use. ISO, for ISOLATED, sends the input signal through an isolation transformer. This can be used to eliminate ground loops or when a low impedance output is desired. When the ground switch is in the left position, the isolation transformer is bypassed entirely and an op-amp buffer provides a low impedance output. Download the manual for the latest features and control layout.

Protected by US Patent

The de Lisle Preamp Power Amp Selector was designed to improve workflow in the studio by eliminating the need to re-cable when switching between numerous preamps and power amps.

Plug in your guitar / pedalboard and send it to any of the 8 connected preamps (or modelers) by rotating the Preamp dial. The preamp's output is then sent to the selected Power Amp. Alternatively, one could connect any line level device to the rear panel Power Amp Input jacks. So, one could be assigned to a power amp, another to a recording interface, external FX, etc. There is also an FX loop between the Preamp and Power Amp which can be bypassed on the front panel.

The Preamp Selector runs off a 2.1mm/5.5mm center negative 12VDC supply, which is boosted internally for increased signal headroom. Preamp inputs are transformer isolated to prevent ground loops. Unused preamps are muted at their input.

The de Lisle Amp-Speaker 8x8 Stereo Deluxe was designed to improve workflow in the studio by eliminating the need to re-cable amps and cabs. This version expands on our previous designs by incorporating simultaneous input switching, a bypassable attenuator loop and D.I.

The 8x8 Stereo Deluxe is our first model to offer two input sources, like stereo outputs from your pedalboard or two guitars. A single source can also be sent to both active amplifiers by flipping the link switch beneath the input jacks. In right toggle position, Input A is routed to the input of the selected amps in both Banks A and B.

Amplifier Banks A/B each have up to 4 amps available for a total of 8. Both Banks have individual attenuator inserts on the rear panel, which can be bypassed with the corresponding front panel switch as well as an after-amp D.I.

Up to 8 cabs are split into sets of 4. The Assign switch allows Speaker A and Speaker B to be routed to either amplifier bank, so you can have Bank A with Speaker A and Bank B with Speaker B, or Bank A with Speaker B and Bank B with Speaker A. The multi-color LEDs under the speaker rotaries will match its assigned amplifier bank.

The 8x8 Stereo Deluxe runs off a 2.1mm/5.5mm center negative 12V supply, which is boosted internally for increased signal headroom. Amplifier inputs are transformer isolated to prevent ground loops. Unused amps are muted at their input and switched to a protective load.

Select below to bundle with our Stereo 100W Impedance Matching Linearly Variable Reactive Attenuator and save $200.00!

Protected by US Patent

The de Lisle Amp-Speaker 4x4 Pro was designed to improve workflow in the studio by eliminating the need to re-cable amps, fx and cabs. This version expands on our previous designs by incorporating simultaneous input switching, fx loop switching and an attenuator loop.

Turning the front panel Amplifier dial will do the following:

• Route the guitar input to the selected amp's input
• Send the amp's output to the selected speaker
• Mute all unused amps at their input
• Switch unused amps to a load
• Route the Pedalboard In / Out to the active amp's FX send and return jacks
• Place unused amp FX loops in bypass

When activated, the attenuator follows the selected amp and cabinet, so you can easily connect your Ox, Fryette, etc. to any combination of amplifier and cabinet. Should you prefer to go straight from amp to cabinet, just place the Attenuator switch in the down position to bypass the attenuator loop. Similarly, the active amp's FX loop can be bypassed by placing the FX Loop switch in the down position.

The 4x4 Pro runs off a 2.1mm/5.5mm center negative 12V supply, which is boosted internally for increased signal headroom. Amplifiers are transformer isolated to prevent ground loops.

Patent Pending.

New features for 2024 models:

There are now three options for amp input switching. DIRECT takes the front panel input and sends it directly to the input of the selected amp, bypassing any additional circuitry. This is the position for normal use. ISO, for ISOLATED, sends the input signal through an isolation transformer. This can be used to eliminate ground loops or when a low impedance output is desired. When the ground switch is in the left position, the isolation transformer is bypassed entirely and an op-amp buffer provides a low impedance output. Download the manual for the latest features and control layout.

Protected by US Patent