de Lisle Amp-Speaker Selector 4×4 Pro Plus

de Lisle Amp-Speaker Selector 4x4 Pro Plus

$1,179.00
de Lisle Amp-Speaker Selector 4x4 Pro Plus
de Lisle Amp-Speaker Selector 4x4 Pro Plus
de Lisle Amp-Speaker Selector 4x4 Pro Plus
de Lisle Amp-Speaker Selector 4x4 Pro Plus
de Lisle Amp-Speaker Selector 4x4 Pro Plus

de Lisle Amp-Speaker Selector 4x4 Pro Plus

$1,179.00
The de Lisle Amp-Speaker 4x4 Pro Plus was designed to improve workflow in the studio by eliminating the need to re-cable amps, fx and cabs. This version expands on our previous designs by incorporating simultaneous input switching, fx loop switching, an attenuator loop, dual speaker mode and a variable line out for going direct into a DAW for use with IRs or cab simulators.

Turning the front panel Amplifier dial will do the following:

• Route the guitar input to the selected amp's input
• Send the amp's output to the selected speaker
• Mute all unused amps at their input
• Switch unused amps to a load
• Route the Pedalboard In / Out to the active amp's FX send and return jacks
• Place unused amp FX loops in bypass

When activated, the attenuator follows the selected amp and cabinet, so you can easily connect your Ox, Fryette, etc. to any combination of amplifier and cabinet. Should you prefer to go straight from amp to cabinet, just place the Attenuator switch in the down position to bypass the attenuator loop. Similarly, the active amp's FX loop can be bypassed by placing the FX Loop switch in the down position.

The 4x4 Pro Plus runs off a 2.1mm/5.5mm center negative 12V supply, which is boosted internally for increased signal headroom. Amplifiers are transformer isolated to prevent ground loops.

Patent Pending.

New features for 2024 models:

There are now three options for amp input switching. DIRECT takes the front panel input and sends it directly to the input of the selected amp, bypassing any additional circuitry. This is the position for normal use. ISO, for ISOLATED, sends the input signal through an isolation transformer. This can be used to eliminate ground loops or when a low impedance output is desired. When the ground switch is in the left position, the isolation transformer is bypassed entirely and an op-amp buffer provides a low impedance output. Download the manual for the latest features and control layout.
Please select a chassis style
Maximum quantity exceeded
Minimum purchase amount of 0 is required
Maximum purchase amount of 0 is allowed
Your Price: $1,179.00
1179.000
Facebook
X
Email
Pinterest
  • Specs
• Input Impedance: 1 Meg
• Output Impedance: 500 Ohm
• Input Sensitivity: +20 Vp-p
• Switching Time: 4-8ms
• Contact Resistance: 0.075 Ohm
• Power Consumption: 2.14W Max
• Guitar / Pedalboard Input (1)
• Amplifier Input (4)
• FX Send (4)
• FX Return (4)
• Amplifier Output (4)
• Speaker Input (4)
• Attenuator Input (1)
• Attenuator Output (1)
• Attenuator Bypass Switch
• Dual Speaker Mode
• FX Bypass Switch
• FX Input
• FX Output
• Adjustable Line Out
• Transformer Isolation
• Internally Isolated DC Power Supply
• Silver Relay Contacts with Gold Overlay
• Protection Loads for Unused Amplifiers
• Auto Muting of Unused Amplifiers
• Auto Bypass of Unused Amplifier FX Loops
• Premium 2U Rack Chassis
• 12VDC 700mA Power Supply Included
• Hand-Wired
• 150W Maximum Power Per Amp
• Lifetime Warranty
• Download Manual

Related Products

  • de Lisle Drop Box Linearly Variable 50W Attenuator

    de Lisle Drop Box Linearly Variable 50W Attenuator

    $229.00

    The de Lisle Drop Box 50W attenuator allows you to knock your amp's volume down to a more manageable level. It's linearly adjustable from -2dB to -18dB. Just insert the Drop Box between your amp's output and the speaker and you're ready to rock!

    ADD TO CART CHECKOUT NOW

    de Lisle Drop Box Linearly Variable 50W Attenuator

    $229.00
    ADD TO CART CHECKOUT NOW
    Successfully Added to your Shopping Cart
    Adding to Cart...
  • de Lisle Amp-Speaker Selector 4x4 Deluxe

    de Lisle Amp-Speaker Selector 4x4 Deluxe

    $599.00
    The de Lisle Amp-Speaker 4x4 Deluxe was designed to improve workflow in the studio by eliminating the need to re-cable amps and cabs. This version expands on our previous designs by incorporating simultaneous input switching and a bypassable attenuator loop.

    Plug in your guitar / pedalboard and send it to any of the 4 connected amps by rotating the Amplifier dial. The amp's output is then sent to the selected speaker cabinet. We've also included an attenuator loop that allows you to easily connect your Ox, Fryette, etc. to any combination of amplifier and cabinet.

    The 4x4 Deluxe runs off a 2.1mm/5.5mm center negative 12V supply, which is boosted internally for increased signal headroom. Amplifier inputs are transformer isolated to prevent ground loops. Unused amps are muted at the input and switched to a protective load.

    Desktop model shown. Rackmount enclosure available as an option.

    New features for 2024 models:

    There are now three options for amp input switching. DIRECT takes the front panel input and sends it directly to the input of the selected amp, bypassing any additional circuitry. This is the position for normal use. ISO, for ISOLATED, sends the input signal through an isolation transformer. This can be used to eliminate ground loops or when a low impedance output is desired. When the ground switch is in the left position, the isolation transformer is bypassed entirely and an op-amp buffer provides a low impedance output. Download the manual for the latest features and control layout.
    Select Options

    de Lisle Amp-Speaker Selector 4x4 Deluxe

    $599.00
    Select Options
    Successfully Added to your Shopping Cart
    Adding to Cart...
  • de Lisle Amp-Speaker Selector 4x4 Pro

    de Lisle Amp-Speaker Selector 4x4 Pro

    $999.00
    The de Lisle Amp-Speaker 4x4 Pro was designed to improve workflow in the studio by eliminating the need to re-cable amps, fx and cabs. This version expands on our previous designs by incorporating simultaneous input switching, fx loop switching and an attenuator loop.

    Turning the front panel Amplifier dial will do the following:

    • Route the guitar input to the selected amp's input
    • Send the amp's output to the selected speaker
    • Mute all unused amps at their input
    • Switch unused amps to a load
    • Route the Pedalboard In / Out to the active amp's FX send and return jacks
    • Place unused amp FX loops in bypass

    When activated, the attenuator follows the selected amp and cabinet, so you can easily connect your Ox, Fryette, etc. to any combination of amplifier and cabinet. Should you prefer to go straight from amp to cabinet, just place the Attenuator switch in the down position to bypass the attenuator loop. Similarly, the active amp's FX loop can be bypassed by placing the FX Loop switch in the down position.

    The 4x4 Pro runs off a 2.1mm/5.5mm center negative 12V supply, which is boosted internally for increased signal headroom. Amplifiers are transformer isolated to prevent ground loops.

    Patent Pending.

    New features for 2024 models:

    There are now three options for amp input switching. DIRECT takes the front panel input and sends it directly to the input of the selected amp, bypassing any additional circuitry. This is the position for normal use. ISO, for ISOLATED, sends the input signal through an isolation transformer. This can be used to eliminate ground loops or when a low impedance output is desired. When the ground switch is in the left position, the isolation transformer is bypassed entirely and an op-amp buffer provides a low impedance output. Download the manual for the latest features and control layout.
    Select Options

    de Lisle Amp-Speaker Selector 4x4 Pro

    $999.00
    Select Options
    Successfully Added to your Shopping Cart
    Adding to Cart...
de Lisle Drop Box Linearly Variable 50W Attenuator

de Lisle Drop Box Linearly Variable 50W Attenuator

$229.00

The de Lisle Drop Box 50W attenuator allows you to knock your amp's volume down to a more manageable level. It's linearly adjustable from -2dB to -18dB. Just insert the Drop Box between your amp's output and the speaker and you're ready to rock!

Maximum quantity exceeded
Minimum purchase amount of 0 is required
￩
￫
de Lisle Amp-Speaker Selector 4x4 Deluxe

de Lisle Amp-Speaker Selector 4x4 Deluxe

$599.00
The de Lisle Amp-Speaker 4x4 Deluxe was designed to improve workflow in the studio by eliminating the need to re-cable amps and cabs. This version expands on our previous designs by incorporating simultaneous input switching and a bypassable attenuator loop.

Plug in your guitar / pedalboard and send it to any of the 4 connected amps by rotating the Amplifier dial. The amp's output is then sent to the selected speaker cabinet. We've also included an attenuator loop that allows you to easily connect your Ox, Fryette, etc. to any combination of amplifier and cabinet.

The 4x4 Deluxe runs off a 2.1mm/5.5mm center negative 12V supply, which is boosted internally for increased signal headroom. Amplifier inputs are transformer isolated to prevent ground loops. Unused amps are muted at the input and switched to a protective load.

Desktop model shown. Rackmount enclosure available as an option.

New features for 2024 models:

There are now three options for amp input switching. DIRECT takes the front panel input and sends it directly to the input of the selected amp, bypassing any additional circuitry. This is the position for normal use. ISO, for ISOLATED, sends the input signal through an isolation transformer. This can be used to eliminate ground loops or when a low impedance output is desired. When the ground switch is in the left position, the isolation transformer is bypassed entirely and an op-amp buffer provides a low impedance output. Download the manual for the latest features and control layout.
Select Options
￩
￫
de Lisle Amp-Speaker Selector 4x4 Pro

de Lisle Amp-Speaker Selector 4x4 Pro

$999.00
The de Lisle Amp-Speaker 4x4 Pro was designed to improve workflow in the studio by eliminating the need to re-cable amps, fx and cabs. This version expands on our previous designs by incorporating simultaneous input switching, fx loop switching and an attenuator loop.

Turning the front panel Amplifier dial will do the following:

• Route the guitar input to the selected amp's input
• Send the amp's output to the selected speaker
• Mute all unused amps at their input
• Switch unused amps to a load
• Route the Pedalboard In / Out to the active amp's FX send and return jacks
• Place unused amp FX loops in bypass

When activated, the attenuator follows the selected amp and cabinet, so you can easily connect your Ox, Fryette, etc. to any combination of amplifier and cabinet. Should you prefer to go straight from amp to cabinet, just place the Attenuator switch in the down position to bypass the attenuator loop. Similarly, the active amp's FX loop can be bypassed by placing the FX Loop switch in the down position.

The 4x4 Pro runs off a 2.1mm/5.5mm center negative 12V supply, which is boosted internally for increased signal headroom. Amplifiers are transformer isolated to prevent ground loops.

Patent Pending.

New features for 2024 models:

There are now three options for amp input switching. DIRECT takes the front panel input and sends it directly to the input of the selected amp, bypassing any additional circuitry. This is the position for normal use. ISO, for ISOLATED, sends the input signal through an isolation transformer. This can be used to eliminate ground loops or when a low impedance output is desired. When the ground switch is in the left position, the isolation transformer is bypassed entirely and an op-amp buffer provides a low impedance output. Download the manual for the latest features and control layout.
Select Options
de Lisle Amp-Speaker Selector 4x4 Pro Plus
de Lisle Amp-Speaker Selector 4x4 Pro Plus
de Lisle Amp-Speaker Selector 4x4 Pro Plus
de Lisle Amp-Speaker Selector 4x4 Pro Plus
de Lisle Amp-Speaker Selector 4x4 Pro Plus