de Lisle Amp-Speaker Selector 4x4 Deluxe
- Specs
• Input Impedance: 1 Meg
• Output Impedance: 500 Ohm
• Input Sensitivity: +20 Vp-p
• Switching Time: 4-8ms
• Contact Resistance: 0.075 Ohm
• Power Consumption: 2.14W Max
• Guitar / Pedalboard Input (1)
• Amplifier Input (4)
• Amplifier Output (4)
• Speaker Input (4)
• Attenuator Input (1)
• Attenuator Output(1)
• Attenuator Bypass Switch
• Transformer Isolation
• Internally Isolated DC Power Supply
• Silver Relay Contacts with Gold Overlay
• Protection Loads for Unused Amplifiers
• Auto Muting of Unused Amplifiers
• Premium Chassis with Laser Etched Panels
• 12VDC 700mA Power Supply Included
• Hand-Wired
• 150W Maximum Power Per Amplifier
• Lifetime Warranty
Related Products
-
de Lisle Drop Box Linearly Variable 50W Attenuator
$229.00The de Lisle Drop Box 50W attenuator allows you to knock your amp's volume down to a more manageable level. It's linearly adjustable from -2dB to -18dB. Just insert the Drop Box between your amp's output and the speaker and you're ready to rock!
Maximum quantity exceededMinimum purchase amount of 0 is requiredde Lisle Drop Box Linearly Variable 50W Attenuator
$229.00Successfully Added to your Shopping CartAdding to Cart... -
￩￫
de Lisle FX Loop Router Switch
$449.00The de Lisle FX Loop Router allows you to effortlessly share your FX between up to 8 amps.
Plug your FX into the rear panel FX Input and FX Output jacks. Then rotate the Amplifier dial to route your FX to any of the connected amp loops. Unused amps are placed in bypass mode to prevent noise. We've also included a front panel Bypass switch for the selected amp and a Ground switch to help eliminate noise.
The FX Loop Router runs off a standard 2.1mm/5.5mm center negative 9V supply (included). We've also provided a "daisy chain" extension jack, so you can connect external 9VDC powered devices.
Desktop model shown. Rackmount enclosure available as an option. -
￩￫
de Lisle Amp-Speaker Selector 4x4 Pro
$999.00The de Lisle Amp-Speaker 4x4 Pro was designed to improve workflow in the studio by eliminating the need to re-cable amps, fx and cabs. This version expands on our previous designs by incorporating simultaneous input switching, fx loop switching and an attenuator loop.
Turning the front panel Amplifier dial will do the following:
• Route the guitar input to the selected amp's input
• Send the amp's output to the selected speaker
• Mute all unused amps at their input
• Switch unused amps to a load
• Route the Pedalboard In / Out to the active amp's FX send and return jacks
• Place unused amp FX loops in bypass
When activated, the attenuator follows the selected amp and cabinet, so you can easily connect your Ox, Fryette, etc. to any combination of amplifier and cabinet. Should you prefer to go straight from amp to cabinet, just place the Attenuator switch in the down position to bypass the attenuator loop. Similarly, the active amp's FX loop can be bypassed by placing the FX Loop switch in the down position.
The 4x4 Pro runs off a 2.1mm/5.5mm center negative 12V supply, which is boosted internally for increased signal headroom. Amplifiers are transformer isolated to prevent ground loops.
Patent Pending.
New features for 2024 models:
There are now three options for amp input switching. DIRECT takes the front panel input and sends it directly to the input of the selected amp, bypassing any additional circuitry. This is the position for normal use. ISO, for ISOLATED, sends the input signal through an isolation transformer. This can be used to eliminate ground loops or when a low impedance output is desired. When the ground switch is in the left position, the isolation transformer is bypassed entirely and an op-amp buffer provides a low impedance output. Download the manual for the latest features and control layout.de Lisle Amp-Speaker Selector 4x4 Pro
$999.00Successfully Added to your Shopping CartAdding to Cart...