de Lisle Amp-Speaker Selector 12×12 with Reactive Attenuator IR Loader

de Lisle Amp-Speaker Selector 12x12 with Reactive Attenuator IR Loader

$1,729.00
de Lisle Amp-Speaker Selector 12x12 with Reactive Attenuator IR Loader
de Lisle Amp-Speaker Selector 12x12 with Reactive Attenuator IR Loader
de Lisle Amp-Speaker Selector 12x12 with Reactive Attenuator IR Loader

de Lisle Amp-Speaker Selector 12x12 with Reactive Attenuator IR Loader

$1,729.00
The de Lisle Amp-Speaker Selector 12x12 with Reactive Attenuator IR Loader was designed to improve workflow in the studio by eliminating the need to re-cable amps and speaker cabinets. This version expands on our previous designs by incorporating a built-in reactive attenuator that can be used as a load box for silent recording along with a transformer isolated impulse response output.

The front panel includes an input for your guitar or pedal followed by a three position power switch; off, direct and isolated. The direct setting takes the front panel input and sends it straight to the amp. Iso employs an transformer isolation to prevent any potential ground loops. Engaging the ground switch while in Iso mode bypasses the transformer while still offering a low impedance buffered output to the amp. Multiple functions are controlled by the Amplifier dial. Selecting positions 1-12 will:

• Route the guitar input to the selected amp's input
• Send the amp's output to the selected speaker
• Mute all unused amps at their input
• Switch unused amps to a load

Easily pair any of your amps with one of up to four connected cabinets by rotating the speaker switch. Should you need to roll back the SPL in the room, but keep your amp operating in the sweet spot, turn on the internal reactive attenuator. Attenuation is linearly variable from -6dB up to -22.5dB. Our unique design eliminates the need for impedance matching at the amp. Just connect your amp's 8 ohm output to the Amp-Speaker Selector, then you can use any cab between 16 and 4 ohms.

Do you still want to be able to connect an Ox, Fryette Power Station or Boss Tube Amp Expander? No problem! The rear panel jacks allow you to insert an external attenuator which disconnects the internal reactive attenuator and D.I. functions.

The Hi-Fi quality, transformer isolated IR Out allows you to go straight into your DAW to load up your favorite IRs or use one of our 10 included impulse responses for a variety of high quality cabs sims.

Included Impulse Responses (See "Sounds" tab below):

01 Vox AC30
02 Marshall 1960AV
03 Marshall 2550
04 Orange PPC
05 Celestion Vintage 30
06 Tweed Bassman
07 Tweed Champ
08 Blackface Twin
09 Mesa Rectifier
10 Ampeg SVT
11 Bypass

Use a TS cable for unbalanced or TRS for a balanced connection to your recording interface. The 12x12 Amp-Speaker Selector with Reactive Attenuator IR Loader can also function as a reactive load box. Just flip the switch to disconnect the speaker and record silently.

The 12x12 Amp-Speaker Selector with Reactive Attenuator IR Loader will quickly become mission control for your studio. Need help deciding which product is the best fit for you? Please feel free to reach out by phone or email. We're happy to help!

Patent Pending.
Maximum quantity exceeded
Minimum purchase amount of 0 is required
Maximum purchase amount of 0 is allowed
Your Price: $1,729.00
1729.000
Facebook
X
Email
Pinterest
  • Specs
• Input Impedance: 1 Meg
• Output Impedance: 500 Ohm
• Input Sensitivity: +20 Vp-p
• Switching Time: 4-8ms
• Contact Resistance: 0.075 Ohm
• Power Consumption: 1.85W Max
• Guitar / Pedalboard Input (1)
• 3 Input Switching Options (Direct, Buffer or Isolated)
• Isolation Transformer Bypass
• Attenuator Level
• Attenuator Bypass Switch
• Silent Recording Switch
• IR Cabinets (10 plus bypass)
• IR Level Control
• IR Ground Switch
• IRs: 24 bit, 44.1kHz, 1024 points (23ms)
• Active Signal LED
• USB Type-C
• Amplifier Input (12)
• Amplifier Output (12)
• Speaker Input (12)
• Attenuator Input (1)
• Attenuator Output(1)
• Transformer Isolation
• Internally Isolated DC Power Supply
• Increased Signal Headroom
• Silver Relay Contacts with Gold Overlay
• Protection Loads for Unused Amplifiers
• Auto Muting of Unused Amplifiers
• 2U Chassis with Laser Etched Panels
• 12VDC 700mA Power Supply Included
• Hand-Wired
• 100W Recommended Maximum Power
• Optimized for 8 Ohms
• Linearly Variable Attenuation to -22.5dB
• Reactive Load Box
• 80hz Resonant Frequency
• Premium US Made Inductors
• Use 16, 8 or 4 Ohm Cabs with the Attenuator
• 20hz-20Khz Transformer Isolated IR
• Lifetime Warranty

Related Products

  • de Lisle 100W Impedance Matching Linearly Variable Reactive Attenuator IR Loader

    de Lisle 100W Impedance Matching Linearly Variable Reactive Attenuator IR Loader

    $749.00
    The de Lisle 100W Reactive Attenuator IR allows you to knock your amp's volume down to a more manageable level while maintaining its natural feel thanks to the reactive load. Attenuation is linearly variable up to -22.5dB. Our unique design eliminates the need for impedance matching at the amp. Just connect the attenuator to your amp's 8 ohm output, then you can use any combination of cabs as long as the total load is between 16 and 4 ohms. Use the transformer isolated IR Out to go straight into your DAW and load up your favorite IRs with the ability to record silently or use one of our 10 included impulse responses for a variety of high quality cabs sims.

    Included Impulse Responses (See "Sounds" tab below):

    01 Vox AC30
    02 Marshall 1960AV
    03 Marshall 2550
    04 Orange PPC
    05 Celestion Vintage 30
    06 Tweed Bassman
    07 Tweed Champ
    08 Blackface Twin
    09 Mesa Rectifier
    10 Ampeg SVT
    11 Bypass
    ADD TO CART CHECKOUT NOW

    de Lisle 100W Impedance Matching Linearly Variable Reactive Attenuator IR Loader

    $749.00
    ADD TO CART CHECKOUT NOW
    Successfully Added to your Shopping Cart
    Adding to Cart...
  • de Lisle 100W Impedance Matching Linearly Variable Reactive Attenuator

    de Lisle 100W Impedance Matching Linearly Variable Reactive Attenuator

    $599.00
    The de Lisle 100W Reactive Attenuator allows you to knock your amp's volume down to a more manageable level while maintaining its natural feel thanks to the reactive load. Attenuation is linearly variable up to -22.5dB. Our unique design eliminates the need for impedance matching at the amp. Just connect the attenuator to your amp's 8 ohm output, then you can use any combination of cabs as long as the total load is between 16 and 4 ohms. Use the transformer isolated D.I. to go straight into your DAW and load up your favorite IRs with the ability to record silently.
    ADD TO CART CHECKOUT NOW

    de Lisle 100W Impedance Matching Linearly Variable Reactive Attenuator

    $599.00
    ADD TO CART CHECKOUT NOW
    Successfully Added to your Shopping Cart
    Adding to Cart...
  • de Lisle Amp-Speaker Selector 4x4 with Reactive Attenuator IR Loader

    de Lisle Amp-Speaker Selector 4x4 with Reactive Attenuator IR Loader

    $1,179.00
    The de Lisle Amp-Speaker Selector 4x4 with Reactive Attenuator IR Loader was designed to improve workflow in the studio by eliminating the need to re-cable amps and speaker cabinets. This version expands on our previous designs by incorporating a built-in reactive attenuator that can be used as a load box for silent recording along with a transformer isolated impulse response output.

    The front panel includes an input for your guitar or pedal followed by a three position power switch; off, direct and isolated. The direct setting takes the front panel input and sends it straight to the amp. Iso employs an transformer isolation to prevent any potential ground loops. Engaging the ground switch while in Iso mode bypasses the transformer while still offering a low impedance buffered output to the amp. Multiple functions are controlled by the Amplifier dial. Selecting positions 1-4 will:

    • Route the guitar input to the selected amp's input
    • Send the amp's output to the selected speaker
    • Mute all unused amps at their input
    • Switch unused amps to a load

    Easily pair any of your amps with one of up to four connected cabinets by rotating the speaker switch. Should you need to roll back the SPL in the room, but keep your amp operating in the sweet spot, turn on the internal reactive attenuator. Attenuation is linearly variable from -6dB up to -22.5dB. Our unique design eliminates the need for impedance matching at the amp. Just connect your amp's 8 ohm output to the 4x4 Amp-Speaker Selector, then you can use any cab between 16 and 4 ohms.

    Do you still want to be able to connect an Ox, Fryette Power Station or Boss Tube Amp Expander? No problem! The rear panel jacks allow you to insert an external attenuator which disconnects the internal reactive attenuator and D.I. functions.

    The Hi-Fi quality, transformer isolated IR Out allows you to go straight into your DAW to load up your favorite IRs or use one of our 10 included impulse responses for a variety of high quality cabs sims.

    Included Impulse Responses (See "Sounds" tab below):

    01 Vox AC30
    02 Marshall 1960AV
    03 Marshall 2550
    04 Orange PPC
    05 Celestion Vintage 30
    06 Tweed Bassman
    07 Tweed Champ
    08 Blackface Twin
    09 Mesa Rectifier
    10 Ampeg SVT
    11 Bypass

    Use a TS cable for unbalanced or TRS for a balanced connection to your recording interface. The Amp-Speaker Selector with Reactive Attenuator IR Loader can also function as a reactive load box. Just flip the switch to disconnect the speaker and record silently.

    The 4x4 Amp-Speaker Selector with Reactive Attenuator IR Loader will quickly become mission control for your studio. Need help deciding which product is the best fit for you? Please feel free to reach out by phone or email. We're happy to help!

    Patent Pending.
    ADD TO CART CHECKOUT NOW

    de Lisle Amp-Speaker Selector 4x4 with Reactive Attenuator IR Loader

    $1,179.00
    ADD TO CART CHECKOUT NOW
    Successfully Added to your Shopping Cart
    Adding to Cart...
￩
￫
de Lisle 100W Impedance Matching Linearly Variable Reactive Attenuator IR Loader

de Lisle 100W Impedance Matching Linearly Variable Reactive Attenuator IR Loader

$749.00
The de Lisle 100W Reactive Attenuator IR allows you to knock your amp's volume down to a more manageable level while maintaining its natural feel thanks to the reactive load. Attenuation is linearly variable up to -22.5dB. Our unique design eliminates the need for impedance matching at the amp. Just connect the attenuator to your amp's 8 ohm output, then you can use any combination of cabs as long as the total load is between 16 and 4 ohms. Use the transformer isolated IR Out to go straight into your DAW and load up your favorite IRs with the ability to record silently or use one of our 10 included impulse responses for a variety of high quality cabs sims.

Included Impulse Responses (See "Sounds" tab below):

01 Vox AC30
02 Marshall 1960AV
03 Marshall 2550
04 Orange PPC
05 Celestion Vintage 30
06 Tweed Bassman
07 Tweed Champ
08 Blackface Twin
09 Mesa Rectifier
10 Ampeg SVT
11 Bypass
Maximum quantity exceeded
Minimum purchase amount of 0 is required
￩
￫
de Lisle 100W Impedance Matching Linearly Variable Reactive Attenuator

de Lisle 100W Impedance Matching Linearly Variable Reactive Attenuator

$599.00
The de Lisle 100W Reactive Attenuator allows you to knock your amp's volume down to a more manageable level while maintaining its natural feel thanks to the reactive load. Attenuation is linearly variable up to -22.5dB. Our unique design eliminates the need for impedance matching at the amp. Just connect the attenuator to your amp's 8 ohm output, then you can use any combination of cabs as long as the total load is between 16 and 4 ohms. Use the transformer isolated D.I. to go straight into your DAW and load up your favorite IRs with the ability to record silently.
Maximum quantity exceeded
Minimum purchase amount of 0 is required
￩
￫
de Lisle Amp-Speaker Selector 4x4 with Reactive Attenuator IR Loader

de Lisle Amp-Speaker Selector 4x4 with Reactive Attenuator IR Loader

$1,179.00
The de Lisle Amp-Speaker Selector 4x4 with Reactive Attenuator IR Loader was designed to improve workflow in the studio by eliminating the need to re-cable amps and speaker cabinets. This version expands on our previous designs by incorporating a built-in reactive attenuator that can be used as a load box for silent recording along with a transformer isolated impulse response output.

The front panel includes an input for your guitar or pedal followed by a three position power switch; off, direct and isolated. The direct setting takes the front panel input and sends it straight to the amp. Iso employs an transformer isolation to prevent any potential ground loops. Engaging the ground switch while in Iso mode bypasses the transformer while still offering a low impedance buffered output to the amp. Multiple functions are controlled by the Amplifier dial. Selecting positions 1-4 will:

• Route the guitar input to the selected amp's input
• Send the amp's output to the selected speaker
• Mute all unused amps at their input
• Switch unused amps to a load

Easily pair any of your amps with one of up to four connected cabinets by rotating the speaker switch. Should you need to roll back the SPL in the room, but keep your amp operating in the sweet spot, turn on the internal reactive attenuator. Attenuation is linearly variable from -6dB up to -22.5dB. Our unique design eliminates the need for impedance matching at the amp. Just connect your amp's 8 ohm output to the 4x4 Amp-Speaker Selector, then you can use any cab between 16 and 4 ohms.

Do you still want to be able to connect an Ox, Fryette Power Station or Boss Tube Amp Expander? No problem! The rear panel jacks allow you to insert an external attenuator which disconnects the internal reactive attenuator and D.I. functions.

The Hi-Fi quality, transformer isolated IR Out allows you to go straight into your DAW to load up your favorite IRs or use one of our 10 included impulse responses for a variety of high quality cabs sims.

Included Impulse Responses (See "Sounds" tab below):

01 Vox AC30
02 Marshall 1960AV
03 Marshall 2550
04 Orange PPC
05 Celestion Vintage 30
06 Tweed Bassman
07 Tweed Champ
08 Blackface Twin
09 Mesa Rectifier
10 Ampeg SVT
11 Bypass

Use a TS cable for unbalanced or TRS for a balanced connection to your recording interface. The Amp-Speaker Selector with Reactive Attenuator IR Loader can also function as a reactive load box. Just flip the switch to disconnect the speaker and record silently.

The 4x4 Amp-Speaker Selector with Reactive Attenuator IR Loader will quickly become mission control for your studio. Need help deciding which product is the best fit for you? Please feel free to reach out by phone or email. We're happy to help!

Patent Pending.
Maximum quantity exceeded
Minimum purchase amount of 0 is required
de Lisle Amp-Speaker Selector 12x12 with Reactive Attenuator IR Loader
de Lisle Amp-Speaker Selector 12x12 with Reactive Attenuator IR Loader
de Lisle Amp-Speaker Selector 12x12 with Reactive Attenuator IR Loader